Welcome, Guest. Please login or register.
Did you miss your activation email?
Wednesday 12 December 2018, 08:36:53 am

Login with username, password and session length

Visit the Official Endian Reference Manual  HERE
13847 Posts in 4212 Topics by 5878 Members
Latest Member: shamhas
Search:     Advanced search
+  EFW Support
|-+  Support
| |-+  VPN Support
| | |-+  Endian 3.0 Community - Problems accessing machines on LAN (Green)
0 Members and 0 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Endian 3.0 Community - Problems accessing machines on LAN (Green)  (Read 8220 times)
nesrual
Jr. Member
*
Offline Offline

Posts: 1


« on: Wednesday 26 March 2014, 10:07:39 pm »

Hi.

I have successfully setup OpenVPN and can connect fine from OSX to the Endian firewall using the Viscosity client.

Our setup runs on Vmware and it's not an option for us to set the network into promiscuous mode.

My LAN (green) network uses the 10.10.10. IP range and I assign IP's from the .200 -> .254 range. When I connect I get an IP address assigned: 10.10.10.200 and I can access the Endian firewall on 10.10.10.1 just fine (Ping, SSH, HTTPS). However I can't access any other machines inside the 10.10.10. network.

My OpenVPN config is as follows:

Device type: TAP
Protocol: UDP
Bridged: YES
Bridgeto: GREEN
Dynamic IP pool start address: 10.10.10.200
Dynamic IP pool end address: 10.10.10.254

I have the following VPN traffic firewall rules as well:

Source: GREEN
Destination: GREEN
Service: <ANY>
Policy: Allow

and

Source: ALL (OpenVPN user)
Destination: GREEN
Service: <ANY>
Policy: Allow

However still no luck.

What am I missing in order to be able to access the internal machines on the GREEN interface via OpenVPN?
Logged
Eduardo
Full Member
***
Offline Offline

Gender: Male
Posts: 13


« Reply #1 on: Thursday 03 July 2014, 11:33:43 pm »

Hi

I have exactly the same problem in my EFW 3.0.  And like me many people have this issue.

/index.php?PHPSESSID=52e7d8494a3cace754b5fcd325c0d39e&topic=4067.0



Check if my LAN (class C) and Remote LAN (class b) are in different segments. Run the OVP client as administrator and also disable the VPN firewall and nothing happens. I only can see my EFW but I can't reach other devices on my remote LAN.

Hope someone can help us if we do something wrong. The configuration is the same that I used in EFW 2.5.1


Regards.

Logged
Eduardo
Full Member
***
Offline Offline

Gender: Male
Posts: 13


« Reply #2 on: Friday 04 July 2014, 05:58:10 am »

The configuration is the same that I used in EFW 2.5.1



Sorry. Is EFW 2.4.1

Logged
Eduardo
Full Member
***
Offline Offline

Gender: Male
Posts: 13


« Reply #3 on: Tuesday 08 July 2014, 04:55:14 am »

If you are running EFW in a virtual machine ENABLE the PROMISCUOUS MODE on the interface connected to the GREEN.


That works for me!
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

Page created in 0.085 seconds with 18 queries.
Powered by SMF 1.1 RC2 | SMF © 2001-2005, Lewis Media Design by 7dana.com